Search results for "exhaust":

EGR Delete Kit – Toyota 20R / 22R / 22RE Engines This complete EGR delete kit is designed to eliminate the Exhaust Gas Recirculation system on Toyota 4-cylinder engines. It improves performance, reduces engine temperatures, and prevents carbon buildup in the intake manifold. Key Features Material: CNC-machined 6061-T6 aluminum alloy Finish: Anodized surface – corrosion and heat resistant Includes: Intake block-off plate, exhaust block-off plates, air plug, gaskets Function: Eliminates EGR flow, reduces soot buildup, improves throttle response Installation: Bolt-on design – may require resistor for EGR temp sensor bypass Fitment Compatibility Engines: Toyota 20R / 22R / 22RE Years: 1975–1995 Fuel Systems: Compatible with EFI and carbureted models Note: Not compatible with 22RET turbocharged platforms Package Includes 2 × Exhaust manifold block-off plates 1 × Intake EGR block-off plate 1 × EFI plenum block-off plate 1 × Air plug 3 × Gaskets Installation Notes Remove EGR valve and associated tubing Install block-off plates using included gaskets Use 10K resistor to bypass EGR temp sensor if equipped Estimated install time: 1–2 hours ⚠️ Legal Disclaimer This product is intended for off-road or closed-course competition use only Not compliant with EPA or CARB emissions standards May trigger check engine light without proper bypass

EGR Delete Block-Off Plate Kit – Ford F-Series / Ranger / Bronco (1983–1997) This CNC-machined EGR delete kit eliminates the exhaust gas recirculation system on select Ford engines, improving throttle response and reducing carbon buildup. Designed for off-road and race applications only. Key Features Material: Aircraft-grade 6061-T6 billet aluminum Finish: Precision CNC cut – warp-resistant and corrosion-proof Includes: 1 × EGR block-off plate, 1 × high-temp gasket, 2 × stainless steel pan-head bolts Function: Seals EGR port on throttle body or intake manifold Design: Direct bolt-on – no welding or tuning required Fitment Compatibility Ford F-150 / F-250 / F-350: 1983–1997 | 4.9L (300), 5.0L (302), 5.8L (351 Windsor) Ford Ranger / Bronco: 1983–1997 | V6 / V8 platforms Also Fits: Mustang, Taurus, E-Series Vans, Lincoln Mark VII, Mercury Cougar, and more Note: Not compatible with VGT turbo systems or electronic EGR modules Installation Notes Clean EGR port and mating surface before installation Use included gasket and bolts – torque to factory spec No ECU tuning required Estimated install time: 20–30 minutes ⚠️ Legal Disclaimer This product is intended for off-road or closed-course competition use only Not compliant with EPA or CARB emissions standards Use on public roads may violate federal or state laws Restore Performance & Reliability Improves Airflow: Eliminates EGR restriction in intake path Reduces Carbon Buildup: Keeps throttle body and intake cleaner Enhances Throttle Response: Improves low-end torque and acceleration Durable Construction: Resists warping, corrosion, and heat fatigue

Exhaust Camshaft Timing Gear – 2.0 TFSI Engines This OEM-style exhaust camshaft gear assembly restores precise valve timing and performance for Audi and Volkswagen vehicles equipped with 2.0 TFSI engines. Designed for direct replacement of worn or noisy cam gears. Key Features OEM reference: 06J109022F / 06J109022G Material: Forged steel gear with anti-corrosion coating Precision-machined teeth for accurate timing Compatible with variable valve timing (VVT) systems Tested for noise, wear, and thermal stability Fitment Compatibility Audi: A3 – 2008–2013 A4 – 2009–2016 A5 – 2010–2017 A6 – 2012–2015 Q3 – 2015–2018 Q5 – 2011–2017 TT – 2009–2015 Volkswagen: Beetle – 2012–2013 CC – 2009–2017 Eos – 2009–2016 GTI – 2008–2014 Jetta / GLI / Wagon – 2008–2013 Passat / Wagon – 2008–2010 Tiguan / Tiguan Limited – 2009–2018 Note: Only compatible with 2.0L TFSI engines. Not suitable for 1.8T or 3.0T variants. Package Includes 1 x Exhaust Camshaft Timing Gear Assembly Installation Notes Professional installation recommended Verify engine code before purchase Check camshaft alignment and timing marks during install Shipping & Warranty Free shipping within USA & Australia Estimated delivery: 3–8 business days 30-day return policy 2-year product guarantee

EGR Delete Kit – Ford 6.4L Powerstroke (2008–2010) This complete EGR delete kit removes the factory exhaust gas recirculation system from your Ford 6.4L Powerstroke engine, improving performance, reliability, and airflow. Ideal for off-road and race-use applications. Key Features Material: TIG-welded aluminum alloy + high-temp silicone seals Includes: Intake elbow, exhaust baffle, brass barb connector, coolant plugs, gaskets, bolts, hose clamps Function: Eliminates EGR flow, reduces soot buildup, lowers exhaust gas temperatures Improves: Turbo spool-up, throttle response, fuel economy Fitment Compatibility Ford Super Duty: 2008–2010 F-250 / F-350 / F-450 / F-550 Engine: 6.4L OHV V8 Powerstroke Turbo Diesel – VIN Code “R” Note: Not compatible with California CARB-certified vehicles Package Includes 1 x Intake Elbow 1 x Exhaust Block-Off Plate 1 x Exhaust Gasket 1 x Brass Barb Hose Connector 2 x Coolant Line Plugs 2 x Plastic Hose Routing Clips 2 x M10-1.25 × 20 Hex Bolts 4 x M10-1.25 × 40 Hex Bolts (Intake Manifold) 4 x M6-1.25 × 25 Flanged Hex Bolts Installation Notes Professional installation recommended Requires removal of EGR valve and cooler ECU tuning required to prevent check engine light Shipping & Warranty Free shipping within USA  Estimated delivery: Mon, Sep 29 – Thu, Oct 2 30-day return policy 2-year product guarantee

EGR Delete Kit – Ford 6.0L Powerstroke Diesel (2003–2007) This complete EGR delete kit is engineered to eliminate the failure-prone EGR system on Ford 6.0L diesel engines. It improves performance, reduces engine temperatures, and prevents coolant leaks and carbon buildup. Key Features Material: TIG-welded 304 stainless steel + CNC-machined billet aluminum Includes: Intake block-off plate, exhaust up-pipe, coolant bypass fittings, mounting hardware, gaskets Function: Removes EGR valve and cooler – improves airflow and reliability Design: Bolt-on fitment – no welding required Fitment Compatibility Ford F-Series: F250 / F350 / F450 / F550 (2003–2007) Ford Excursion: 2003–2005 Ford E-Series Vans: E250 / E350 / E450 (2005–2010) Engine: 6.0L Powerstroke Diesel Note: Not compatible with Cab & Chassis platforms or updated EGR retrofit systems Package Includes 1 × Intake block-off plate 1 × Exhaust up-pipe (welded flange) 1 × Coolant bypass fitting 1 × Air plug Gaskets, bolts, washers, nuts Installation Notes Disconnect battery and drain coolant before installation Remove EGR valve, cooler, and associated tubing Install block-off plates and bypass fittings ECU tuning recommended to avoid check engine light Estimated install time: 2–3 hours ⚠️ Legal Disclaimer This product is intended for off-road or closed-course competition use only Not compliant with EPA or CARB emissions standards May void manufacturer warranty – consult your dealer before installation

EGR Block-Off Plate Kit – Toyota V6 3.0L 3VZ-E (1988–1995) This complete EGR delete kit is designed to eliminate the exhaust gas recirculation system on Toyota 3VZ-E engines. Ideal for off-road use or performance builds, it prevents carbon buildup and improves throttle response. Key Features Material: CNC-machined T6061 aluminum alloy Finish: Anodized surface – corrosion & heat resistant Design: Thicker plate prevents warping or deformation Function: Blocks exhaust gases from re-entering intake, improves fuel economy Fitment Compatibility Toyota T100: 1993–1994 Toyota Pickup: 1988–1995 Toyota 4Runner: 1988–1995 Engine: V6 3.0L 3VZ-E only Note: Not compatible with 3VZ-FE or 5VZ-FE engines Package Includes 3 × EGR Block-Off Plates 2 × Vacuum Caps Optional: 10K & 5.7K resistors for CEL bypass (not included) Installation Notes Remove EGR valve, pipe, and solenoid Install block-off plates using factory bolts or high-temp hardware Use vacuum caps to seal unused ports Optional: Install resistors to simulate EGR temp signal and avoid CEL Legal Disclaimer For off-road or race-track use only Not legal for highway use in emissions-regulated areas User assumes full responsibility for installation and use Shipping & Warranty Free shipping within USA Estimated delivery: Tue, Sep 30 – Fri, Oct 3 30-day return policy 2-year product guarantee

Description:100% brand new, Never been tried or installedMade from SUS409 SteelThickness: 2mmInlet Diameter: 4.0"Get rids of restricting cat pipes and mufflers. (catless, decat, test pipe)Easy InstallationIncreased performanceIncreased economyContour bent hangersPreformed band clampsEasy & Quick Bolt on DesignUtilizes Factory HangersProfessional installation is highly recommendedPackage including:4" turbo 2 piece race pipe kit - (Part # 857nb)EGR SolutionAs Pictures ShownFitment:2011-17 Ford 6.7L Powerstroke F250/350 PickupDPF / CAT Race pipeFor Exact Years and Models, Please Check Compatibilities

Repair garages and middlemen can contact us to get wholesale prices Fitment Guide: Trucks 2006-2007.5 Silverado 2500HD 3500HD 6.6L LBZ Duramax 2006-2007.5 Silverado 3500 6.6L LBZ Duramax 2006-2007.5 Serra 2500HD 3500HD 6.6L LBZ Duramax 2006-2007.5 Sierra 3500 6.6L LBZ Duramax Vans 2006-2007.5 Express Van 2500 3500 6.6L LBZ Duramax Package Contents: 2*Billet Black Powder Coated Intake Block Off Plate with O-Ring Seals 1*Exhaust Block Off Plate 1*Intake Support Bracket 1*Support Bracket Washer 2*Hose Clamps 2*M8 Flange Nuts 2*M8 x 20 Cap Head Bolts 2*M8 x 30 Cap Head Bolts 2*M8 x 25 Hex Head Bolts 2*M10 x 20 Hex Head Bolts 1*Black Coolant Tube Cross Reference Part Numbers: NP-LBZEGRKIT   Performance Off-Road Use Only  NOT LEGAL for use in pollution controlled vehicles that are operated on public streets, roads or highways. Requires use of a tuner to Run the EGR Delete. Attention: Legal Disclaimer: This product may NEVER be installed on a vehicle registered for highway or public street use. By installing this product onto your vehicle, you assume all risk and liability associated with its use. It is your responsibility to make sure your vehicle complies with all federal, state, and local emissions laws. Federal and many state and local laws prohibit the removal, modification or rendering inoperative of any part of the design affecting emissions or safety on motor vehicles used on a public street or highway. Violation may result in a fine of up to $32,500 per vehicle (or possibly higher depending on changes in the law). All civil penalties and fines for removing your vehicle's emissions equipment are the sole responsibility of the end user. No other applications besides off-road competition racing use are intended or implied. Depending on where you live, additional restrictions may apply. Check all applicable laws before installing or using. Not available for sale or use in the state of California, Colorado and Arizona. In addition, we are looking for long-term cooperative auto parts agents. We are mainly engaged in auto parts of American models, lawn mower parts, ATV, UTV parts, RV parts, ship parts and tool goods. If you need other products, please contact us and we will give you unexpected prices.

Description：Fits most LS series intake manifolds including LQ4 and many other truck manifoldsatural finish aluminum as shown, includes intake plug, exhaust block off plate, exhaust gasket, stainless steel bolts and O-ringPackage：1 x For LS EGR Delete Set

EGR Delete Kit – Chevy Camaro LS1 / LS6 (1999–2002) This precision-machined EGR delete kit removes the factory exhaust gas recirculation system from your LS1 or LS6 engine, improving airflow, throttle response, and engine cleanliness. Ideal for off-road and performance builds. Key Features Material: CNC-machined 6061-T6 aircraft-grade aluminum Finish: Anodized coating – corrosion-resistant, high-temp stable Includes: 3 block-off plates (intake & exhaust), 1 intake plug, 1 O-ring, 7 stainless steel bolts Function: Eliminates EGR flow, reduces carbon buildup, improves idle and throttle response Fitment Compatibility Chevrolet Camaro: 1999–2002 Trims: Z28 / SS Engines: LS1 / LS6 Transmissions: T56 manual / 4L60E automatic Note: Compatible with factory intake manifold. ECU tuning recommended to disable EGR logic. Package Includes 3 x EGR Block-Off Plates 1 x Intake Plug 1 x O-Ring Seal 7 x Stainless Steel Bolts Installation Notes Direct bolt-on installation Requires removal of EGR valve and associated tubing ECU tuning recommended to prevent check engine light Shipping & Warranty Free shipping within USA & Australia Estimated delivery: Mon, Sep 29 – Thu, Oct 2 30-day return policy 2-year product guarantee

EGR Valve & Cooler Delete Kit – Duramax LML 6.6L (2011–2015) This complete EGR delete kit removes the factory exhaust gas recirculation system from your GMC/Chevy 6.6L Duramax LML engine, improving performance, reliability, and airflow. Ideal for off-road and race-use applications. Key Features Material: TIG-welded stainless steel + billet aluminum Includes: Air intake closing plate, exhaust block-off plate, 3-terminal coolant hose, clamps, bolts Function: Eliminates EGR flow, reduces soot buildup, lowers exhaust gas temperatures Improves: Turbo spool-up, throttle response, fuel economy, coolant temperature (drops ~5–8°C) Fitment Compatibility Chevrolet Silverado: 2500HD / 3500HD (2011–2015) GMC Sierra: 2500HD / 3500HD (2011–2015) Engine: 6.6L Duramax LML Diesel – VIN Code “L” Note: Not compatible with California CARB-certified vehicles Package Includes 1 x Air Intake Closing Plate 1 x Exhaust Block-Off Plate 1 x 3-Terminal Coolant Hose 4 x Stainless Steel Clamps 8 x Mounting Screws Installation Notes Professional installation recommended Requires removal of EGR valve and cooler ECU tuning required to prevent check engine light Shipping & Warranty Free shipping within USA & Australia Estimated delivery: Mon, Sep 29 – Thu, Oct 2 30-day return policy 2-year product guarantee

Repair garages and middlemen can contact us to get wholesale prices   Ford SVT Mustang Cobra EGR Delete Kit Billet aluminum IAC (idle air control) and EGR (exhaust gas recirculation) block off plates add a distinctive touch to your throttle body. Designed for off-road use only when one or both controls have been eliminated for racing purposes.----Use to Delete Egr Valve----Precision CNC Machined From Aircraft Grade 6061 T6 Aluminum----Will Not Warp or Deform Like other Thinner Delete PlatesProduct Detail:Condition:NewPlacement on Vehicle:FrontPackage Including:1 x EGR Delete Plate + Bolts + Exhaust CapFitment(For):Ford SVT Mustang Cobra 1996-2004 In addition, we are looking for long-term cooperative auto parts agents. We are mainly engaged in auto parts of American models, lawn mower parts, ATV, UTV parts, RV parts, ship parts and tool goods. If you need other products, please contact us and we will give you unexpected prices.  

EGR Valve & Cooler Delete Kit – 6.6L Duramax LLY (2004.5–2005) This complete EGR delete kit is engineered to remove the factory EGR valve and cooler from GM 6.6L Duramax LLY engines. It improves airflow, lowers engine temperatures, and enhances reliability for off-road and competition use. Key Features Material: CNC-machined 7075 aluminum + TIG-welded stainless steel bracket Includes: Intake block-off plates, exhaust block-off, coolant bypass hose, clamps, bolts, nuts, gasket maker Function: Eliminates EGR flow and cooler – reduces soot buildup and coolant leaks Design: Bolt-on fitment – clean engine bay appearance Fitment Compatibility Chevrolet Silverado 2500HD / 3500: 2004.5–2005 | 6.6L Duramax LLY | VIN “2” GMC Sierra 2500HD / 3500: 2004.5–2005 | 6.6L Duramax LLY | VIN “2” Note: Not compatible with LB7, LBZ, LMM, or LML platforms Package Includes 2 × Intake block-off plates with rubber seal 1 × Nickel-plated exhaust block-off plate 1 × Stainless steel support bracket 1 × Coolant bypass hose (430mm) 2 × Hose clamps 4 × M8 × 20mm bolts + 4 × M8 × 30mm bolts 1 × M10 × 20mm bolt + 2 × M8 flanged nuts 1 × Gasket maker Installation Notes Disconnect battery and drain coolant before installation Remove EGR valve, cooler, and associated tubing Install block-off plates and bypass hose ECU tuning required to disable EGR function and avoid fault codes Estimated install time: 2–3 hours ⚠️ Legal Disclaimer This product is intended for off-road or closed-course competition use only Not legal for use on public roads or pollution-controlled vehicles Not available for sale or use in California, Colorado, or Arizona

Rear Cam Plug with Seal – OEM-Compatible 12513-P72-003 This cylinder head rear cam plug seals the exhaust camshaft hole at the back of the cylinder head, preventing oil leaks and maintaining proper crankcase pressure. Made from high-temp rubber and pre-installed with sealing ring. Key Benefits Prevents oil seepage from rear camshaft bore OEM-style fitment for B/D/F/H-series cylinder heads Durable rubber construction resists heat and oil degradation Direct-fit replacement; no modification required Fitment Compatibility Honda Civic (1992–2015) Honda CR-V (1997–2006) Honda CR-Z (2011–2016) Honda HR-V (2016–2020) Honda Insight (2010–2014) Honda Fit (2007–2013) Honda Civic del Sol VTEC (1996–1997) – B16A2 DOHC Acura Integra (1990–2001) Replaces OEM Part Numbers 12513-P72-003 12513P72003 225-01023-310 KF811285 What's Included 1 x Cylinder Head Rear Cam Plug (with pre-installed seal) Notes Not compatible with K-series or turbocharged engines Ensure proper seating during installation to avoid oil leaks Estimated install time: 10–15 minutes Engine Seal Restoration Ideal for engine rebuilds or oil leak repairs. This plug ensures a tight seal at the rear cam bore, protecting internal components and maintaining oil pressure integrity.

Description 100% Brand New Color: Black Complete EGR Delete Kit for 6.7L Powerstroke Completely Replaces EGR System, No Other Parts Required CNC Machined Billet Aluminum and Stainless Steel Completes Coolant Circuit Exhaust Cover Plate Tapped for Ford Factory EGT Probe Professional installation is highly recommend (No Instruction Included) Fitment 2017-2019 Ford F-250 F-350 F-450 F-550 6.7L V8 POWERSTROKE DIESEL TURBO Package includes 1 X EXHAUST MANIFOLD BLOCK-OFF PLATE, PRE-WELDED FOR AN EGT SENSOR 1 X INTAKE BLOCK-OFF PLATE 1 X COOLANT BLOCK-OFF PLATE 1 X STAINLESS 1" HOSE CLAMP 1 X VACCUM CAP 1 X PRESSURE SENSOR BRACKET 1 X PRESSURE SENSOR BRACKET HARDWARE 2 X 3/4" COOLANT CAPS 3 X 8MM BOLTS 3 X 8MM FLAT WASHERS 3 X ZIP-TIES